laws:orthopla
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
laws:orthopla [2025/10/17 17:37] hangbiao [List of state variables] |
laws:orthopla [2025/10/21 10:06] (current) hangbiao [Integer parameters] |
||
|---|---|---|---|
| Line 106: | Line 106: | ||
| |:::| 1 : Damage on elastic properties | | |:::| 1 : Damage on elastic properties | | ||
| |IHSS| = 0 : nothing | | |IHSS| = 0 : nothing | | ||
| - | |:::| 1 : Coupling stiffness-deformation | | + | |:::| 1 : Deformation on elastic properties (Small strain stiffness) | |
| |ICOH| = 0 : nothing | | |ICOH| = 0 : nothing | | ||
| - | |:::| 1 : Coupling cohesion-temperature | | + | |:::| 1 : Temperature on cohesion | |
| |INONL| = 0 : nothing | | |INONL| = 0 : nothing | | ||
| - | |:::| 1 : Coupling stiffness-mean effective stress | | + | |:::| 1 : Mean effective stress on elastic properties | |
| ==== Real parameters ==== | ==== Real parameters ==== | ||
| Line 167: | Line 167: | ||
| |Gamma7|equivalent strain at which the Young's modulus has reduced to 0.7 times | | |Gamma7|equivalent strain at which the Young's modulus has reduced to 0.7 times | | ||
| |Aa|Fitting parameter | | |Aa|Fitting parameter | | ||
| - | ^ Line 8 (7G10.0) (Only if IECPS = 2 or 3) ^^ | + | ^ Line 8 (3G10.0) (Non-linearity) ^^ |
| + | |RCON|Referential mean effective stress| | ||
| + | |AMINCON|Minimum mean effective stress (defined to limitate the minimum stiffness)| | ||
| + | |ANE|Exponent to adapt different material properties| | ||
| + | ^ Line 9 (7G10.0) (Only if IECPS = 2 or 3) ^^ | ||
| |PSICPEAK| Peak of dilatancy angle for compressive paths (If IECPS=2 then PSICPEAK is the initial value of dilatancy angle| | |PSICPEAK| Peak of dilatancy angle for compressive paths (If IECPS=2 then PSICPEAK is the initial value of dilatancy angle| | ||
| |PSICLIM| Limit value of dilatancy angle for compressive paths| | |PSICLIM| Limit value of dilatancy angle for compressive paths| | ||
| Line 175: | Line 179: | ||
| |PSIELIM| Limit value of dilatancy angle for extensive paths| | |PSIELIM| Limit value of dilatancy angle for extensive paths| | ||
| |DECPSI| Value of EEQU when the dilatancy angle has been half decreased between its initial and final values| | |DECPSI| Value of EEQU when the dilatancy angle has been half decreased between its initial and final values| | ||
| - | ^ Line 9 (2G10.0) (Only if IDAM = 1) ^^ | + | ^ Line 10 (2G10.0) (Only if IDAM = 1) ^^ |
| |P|Parameter controlling the damage evolution rate| | |P|Parameter controlling the damage evolution rate| | ||
| |YD0|Initial threshold| | |YD0|Initial threshold| | ||
laws/orthopla.1760715470.txt.gz · Last modified: 2025/10/17 17:37 by hangbiao
Page Tools
