Lagamine

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Appendix 8: Water retention curves, water and air relative permeability curves and thermal conductivity function ======
===== Water Retention Curves =====

In this appendix, the different laws expressing the Water Retention Curves in FKRSAT.F are presented, along with their equations and parameters.

/!\ Not all laws are compatible with FKRSAT, only: /!\\\
155-119-120-126-127-128-171-172-173-174-175-180-197-95-198-196-176-177-199-194-182-629 

^ISR = 0 - Saturated medium^^
The saturation degree stays equal to one: \[S_w = 1\]

^ISR = 1 ^^
\[S_w = S_{r,field}-CSW1\left(\frac{s}{CSW3}\right)^{CSW2}\] 
The suction is defined as $s=p_a-p_w$ and $CSR3$ can be taken equal to $\rho_w.g.C^{ste}$. 

^ISR = 2 ^^
\[ -\frac{s}{\rho_wg} =  \begin{cases}   -10.214\exp(-15.27S_w+6.062)  & \quad \text{if } 0.1<S_w<1 \\   -10.214\exp(314.84S_w^2-78.24S_w+9.21)   & \quad \text{if } 0<S_w<0.1  \end{cases}\]

^ISR = 3 ^^ 
\[ S_e(p_c)=  \begin{cases}  CSR3+\left(1+\left(\frac{p_c}{CSR1}\right)^{\frac{1}{1-CSR2}}\right)^{-CSR2} & \quad \text{if } p_c>0 \\ 1 & \quad \text{if } p_c \leq 0 \end{cases}\]

^ISR = 4 ^^
 \[S_w = \begin{cases} CSR1 * ln\left(\frac{s}{10^6}\right) +CSR2 & \quad \text{if } 0.26 \text{ MPa}<s<222\text{ MPa} \\ S_{res}  & \quad \text{if } s>222 \text{ MPa} \\ S_{r,field}  & \quad \text{if } s<0.26 \text{ MPa}\end{cases}\]

^ISR = 5 - Van Genuchten formulation^^ 
\[S_w = S_{res} + (S_{max}-S_{res})\left(1+\left(\frac{s}{CSR1}\right)^{CSR2}\right)^{-\left(1-\frac{1}{CSR2}\right)}\]

^ISR = 6^^
 \[S_w = S_{res}+\frac{CSR3*(S_{r,field}-S_{res})}{CSR3+(CSR1*s)^{CSW2}}\]

^ISR = 7 ^^
 \[S_w=\frac{CSR1 \log(s*10^{-6})+CSR2}{100} \\ \text{If } S_w<S_{res} => S_w = S_{res} \\ \text{If } S_w>S_{r,field} => S_w = S_{r,field}\]


^ISR = 8^^
 \[S_w=\frac{CSR3}{\pi}\arctan\left(-\frac{s+CSR2}{CSR1}\right)+\frac{CSR3}{2}\] {{ :appendices:a8_1.png?300 |}}

^ISR = 9 -  Quasi-saturated soils (XL2)^^
\[S_w= \left(1+ \frac{p_w}{p_a}\right)*S_{r,field}*\frac{1}{1+\frac{p_w}{p_a}*S_{r,field}*(1-HENRY)}\]

^ISR = 10 - Fixed WRC (Comparaison eclipse)^^

^ISR = 11 - Fixed WRC (Comparaison eclipse)^^

^ISR = 12 - Fixed WRC (Comparaison eclipse)^^

^ISR = 13^^
\[S_w= CSW3*\left(\frac{\arctan\left(-(s+CSW2)/CSW1\right)}{\pi}+0.5\right)\]

^ISR = 14 - Fixed WRC (Comparaison eclipse)^^


^ISR = 15 - Andra for swelling clay (MX80)^^
\[COEFM  = 1-\frac{}{CSW2}\]
\[S_w= \left(\left(1+\left(\frac{s}{CSW3}\right)^{COEFM}\right)^{-CSW1}\right)*\left(1-\frac{s}{CSW4}\right)^{CSW2}\]

^ISR = 16 - Andra for argilities - Van Genuchten^^
\[COEFM  = 1-\frac{}{CSW2}\]
\[SATUR  = (1-CSW3-CSW4)*(1D0+(PC/CSW1)**CSW2)**(-COEFM)+CSW3\]

^ISR = 17 -  (EPFL-LMS, Lausanne)^^
Parameter correspondance: \\ CSW1=$\beta_h$ \\ CSW2=$s_{hys}$ \\ CSW3=$\theta_T$ \\ CSW4=$\theta_e$ \\ CSW5=RETINI 

An elasto-plastic approach is used to describe the curve of retention of the soil. This implies two plastic mechanisms:
→ A mechanism activated during drying $f_{dry}=s-s_d=0$
→ A mechanism activated during the wetting $f_{wet}=s_d s_{hys} - s=0$
Where $s_d$ is the drying limit and $s_{hys}$ is a parameter defining the opening of the hydric hysteresis. When a mechanism is activated, $s_d$ evolves according to the following exponential law: $s_d=s_{d0}\exp(-\beta_h \Delta S_w)$ {{ :appendices:a8_2.png?300 |}}

The effects of mechanical deformation and of temperature on the retention curve are considered through the evolution of the entering air suction: \[s_e=s_{e0}\exp(-\beta \Delta S_w)\left[1-\theta_T\log(T/T_0)-\theta_e \log(1-\varepsilon_v)\right]\] In order to characterize the initial degree of saturation inside the hydric hysteresis, the RETINI parameter is used. At the initial state, for a given suction, if RETINI = 0, the point is on the drying curve; if RETINI = 1, the point is on the wetting curve. RETINI can also take a value between 0 and 1. In that case, the saturation degree is determined using a linear interpolation between the drying curve and the wetting curve.

^ISR = 18 - (EPFL-LMS, Lausanne)^^
Parameter correspondance: \\ CSW1=$s_{D0}$ \\ CSW2=$\kappa_H$ \\ CSW3=$\beta_H$ \\ CSW4=$\pi_H$ \\ CSW5=RETINI

The water retention curve is modeled using an elasto-plastic approach with kinematic hardening (ACMEG-s model, LMS, EPFL) {{ :appendices:a8_3.png?300 |}} The yield surface delimiting the elastic domain takes the following form: \[f=\left\Vert ln\left(\frac{s}{s_D}\right)+\frac{1}{2}ln\left(\frac{s_{D0}}{s_{eH}}\right)\right\Vert - \frac{1}{2} ln \left(\frac{s_{D0}}{s_{eH}}\right)\] The saturation degree $S_w$ can be decomposed in an elastic part $S_w^e$ and a plastic part $S_w^p$: \[S_w = S_w^e+S_w^p\] The elastic part is defined by parameter $\kappa_H$ \[S_w^e=1- \frac{1}{\kappa_H}ln\frac{s}{s_{eH}}\] The plastic part is defined by: \[S_w^p=S_w^D-\frac{1}{\beta_H}\ln\frac{s}{s_D}\] The saturation degree cannot be higher than 1 or lower than $S_{res}$.

The entering air suction $s_{eH}$ evolves with the total volumic deformation: \[s_{eH}=s_e+\pi_H*\varepsilon_v\] In order to characterize the initial degree of saturation inside the hydric hysteresis, the RETINI parameter is used. At the initial state, for a given suction, if RETINI = 0, the point is on the drying curve; if RETINI = 1, the point is on the wetting curve. RETINI can also take a value between 0 and 1. In that case, the saturation degree is determined using a linear interpolation between the drying curve and the wetting curve.

^ISR = 19 - ISR = 5 with the addition of AIREV^^
\[S_w = \begin{cases} 1 & \quad \text{if } s < \text{AIREV} \\ S_{res}+(S_{max}-S_{res})\left(1+\left(\frac{s-AIREV}{CSR1}\right)^{CSR2}\right)^{-\left(1-\frac{1}{CSR2}\right)} & \quad \text{if } s > \text{AIREV} \end{cases}\]

^ISR = 20^^
\[SATUR  = SRES+(SRFIELD-SRES)*(1D0+(PC/PR)**CSW2)**(-COEFM)\]

^ISR=21 - Andra for Bentonite (UPC)^^
\[COEFM  = ONE-ONE/CSW2\]
\[SATUR  = (ONE+(PC/CSW1)**CSW2)**(-COEFM)*(ONE-PC/CSW3)**CSW4\]

^ISR = 22 - Romero et al., 2011^^

^ISR = 23 - Unconstant parameters, function of the porosity^^
For laws WADUA, CLEATF and WPROG. (François BERTRAND).

^ISR = 25 - Van Genuchten with "true" air-entry pressure (aept).^^
\[COEFM  = 1-\frac{1}{CSW2}\]
\[S_w  = S_{res}+(S_{r,field}-S_{res})*\left(1+\left(\frac{s-AEPT}{CSW1}\right)^{CSW2}\right)^{-COEFM}\]

^ISR = 26 - Double structure mechanism adsorption^^
\[e_w=e_{wM}+e_{wm}\] \[e_w=e_m \exp \left(-(C_{ads}s)^{n_{ads}}\right) + (e-e_m) \left[1+\left( (e-e_m)\frac{s}{A}\right)^n\right]^{-m} \] \[S_r=\frac{e_w}{n}\] $n$=porosity \\ CSR1 = $A$ \\ CSR2 = $m$ \\ CSR3 = $n$ \\ CSR4 = $C_{ads}$ \\ CSR5 = $n_{ads}$

^ISR = 27^^
\[SATUR  = DEXP(-PC/CSW1)\]

^ISR = 50 - For Mothymar law^^ 
\[S_w = 1 * \left(1+\left(\frac{s}{CSR1}\right)^{CSR2}\right)^{CSR3}\]
\[S_{w,mic} = 1 * \left(1+\left(\frac{s}{CSR4}\right)^{CSR2}\right)^{CSR5}\]

^ISR = 52 ISR=5 with independent CSW2 and COEFM^^ 
\[S_w = S_{res} + (S_{max}-S_{res})\left(1+\left(\frac{s}{CSR1}\right)^{CSR2}\right)^{CSR3}\]

^ISR = 53 - ISR=5 with hysteresis implemented.^^ 

The main water retention curves (d=drying, w=wetting) are, according to the Van Genuchten model:
\[S_{ed} = S_{res} + (S_{max}-S_{res}) \left[1 + \left(\frac{s}{a_d}\right)^{n_d}\right]^{-m_d}\] 
\[S_{ew} = S_{res} + (S_{max}-S_{res}) \left[1 + \left(\frac{s}{a_w}\right)^{n_w}\right]^{-m_w}\]

The hysteresis is then defined by:
\[\frac{\partial S_{es}}{\partial s} (\text{wetting}) = \left(\frac{s_w}{s}\right)^b\left(\frac{\partial S_{ew}}{\partial s}\right) \text{ with } s_w = a_w \left(S_e^{-1/m_w}-1\right)^{1/n_w}\] 
\[\frac{\partial S_{es}}{\partial s} (\text{drying}) = \left(\frac{s_d}{s}\right)^{-b}\left(\frac{\partial S_{ed}}{\partial s}\right) \text{ with } s_d = a_d \left(S_e^{-1/m_d}-1\right)^{1/n_d}\]

And therefore: \[S_e^{t+1} = S_e^t + \left(\frac{\partial S_{es}}{\partial s}\right)\times ds\] 

The ISR=53 parameters are: CSRW1=$a_d$, CSRW2=$n_d$, CSRW3=$a_w$, CSRW4=$n_w$ and CSRW5=$b$.

/!\ Two parameters must be passed through the DUM argument of FKRST: DUM(1)=$s^{t-1}$ and DUM(2)=$S_w^{t-1}$.

^ISR = 55, Soil water retention curve considering gas entry pressure (EURAD-Gas Task4.2).^^ 

In the below formulations, $p_c$ and is the capillary pressure ($p_c=p_{air}-p_{water}$), $α$ is the inverse of air-entry pressure i.e., $P_r$, $S_e$ is the effective degree of water saturation, $S_l$ is the degree of water saturation, $S_r$  is residual degree of water saturation, $S_e^*$ is the effective degree of saturation considering the explicit gas entry pressure i.e., $P_e$, $ε$ is a numerical parameter (0.01 or 0.001), $m$ and $n$  are fitting parameters.

\[ p_c= \begin{cases} -\frac{1}{\alpha}\left ( \left ( S_{e}^{*}S_{e}\right )^{-\frac{1}{m}}-1\right)^{\frac{1}{n}}, \quad \text{if} \; S_{e}\leq 1-\varepsilon
\\ 
-\frac{1}{\alpha}\left ( \left ( S_{e}^{*}S_{e}\right )^{-\frac{1}{m}}-1\right)^{\frac{1}{n}}.\left ( \frac{1-S_{e}}{\varepsilon } \right ), \quad \text{if} \; \left ( 1-\varepsilon \right ) < S_{e}< 1
\\ 
0, \quad \text{if} \; S_{e}=1
\end{cases}\].

\[ S_{e}=\frac{S_{l}-S_{r}}{1-S_{r}}\]
\[ S_{e}^{*}=\left ( 1+\left (\alpha P_{e}  \right )^{n}  \right )^{-m}\]
\[ m=\left ( 1-\frac{1}{n} \right )\]
\[ \alpha =\frac{1}{P_{r}}\]

So as per the above formulations, the required parameters are as follows:

**CSR1** = Air-entry pressure i.e., $P_r$ 

**CSR2** = $n$

**CSR3** = Gas entry pressure i.e., $P_e$

**CSR4** = $\varepsilon$

**CSR5** = Residual degree of water saturation i.e., $S_r$

**CSR6** = Max. degree of water saturation i.e., 1

**CSR7** = NIL

/**NOTE**\ The above water retention curve is implemented in conjunction with the water and air relative permeability functions which also consider the effect of gas entry pressure. It is advised to go through these formulations i.e., **IKW=55** for relative permeability function for water and **IKA=55** for air.



===== Water relative permeability =====

^IKW = 0^^  
\[k_{rw} = 1\]

^IKW = 1^^   
\[k_{rw} = CKW3 - CKW1 (1-S_{r,w})^{CKW2}\] 
Example: CKW1 = 2.207; CKW2 = 0.953; CKW3 = 1

^IKW = 2^^ 
\[k_e^{rel} (S_e) = \left(1+\left(S_{r,w}^{CKW1} - 1\right)^{CKW2}\right)^{-1}\] 
Example: Momas: CKW1 = -2.429; CKW2 = 1.176

^IKW = 3^^   
\[k_{r,w} = \begin{cases} \exp(CKW1*S_w+CKW2*S_w^2) & \quad \text{if } S_w \geq S_{res} \\ k_{r,min} & \quad \text{if } S_w<S_{res} \end{cases} \]

^IKW = 4^^ 
\[k_{r,w} = \begin{cases} \frac{(S_w-S_{res})^{CKW1}}{(S_{r,field}-S_{res})^{CKW2}} & \quad \text{if } S_w \geq S_{res} \\ k_{r,min} & \quad \text{if } S_w<S_{res} \end{cases} \] __Example__: $CKW1 = 4$; $CKW2 = 4$; $S_{r,field} = 1$; $S_{res}=0.1$

^IKW = 7^^ 
 
\[k_{rw}=\sqrt{S_{rw}} \left(1-\left(1-S_{rw}^{\frac{1}{CKW1}}\right)^{CKW1}\right)^2\]

^IKW = 8^^ 
 \[k_{rw} = S_{rw}^3\]

^IKW = 9^^  
\[k_{rw}=\sqrt{S_{we}} \left(1-\left(1-S_{we}^{\frac{1}{CKW1}}\right)^{CKW1}\right)^2\] 
\[S_e=\frac{S_{rw}-S_{rw,res}}{1-S_{rw,res}-S_{rg,res}}\] \[S_{rw,res}=CKW2\] \[S_{rg,res}=CKW3\]

^IKW = 55, Relative permeability function for water considering gas entry pressure (EURAD-Gas Task4.2).^^ 

Similar to **ISR = 55**, $p_c$ is the capillary pressure ($p_c=p_{air}-p_{water}$), $α$ is the inverse of air-entry pressure i.e., $P_r$, $S_e$ is the effective degree of water saturation, $S_l$ is the degree of water saturation, $S_r$  is residual degree of water saturation, $S_e^*$ is the effective degree of saturation considering the explicit gas entry pressure i.e., $P_e$, $m$ and $n$  are fitting parameters.

\[ k_{rw}= \begin{cases} \sqrt{S_{e}}\left [ \frac{1-\left ( 1-\left (S_{e}^{*}S_{e} \right )^{1/m} \right )^{m}}{1-\left ( 1-\left (S_{e}^{*}\right )^{1/m} \right )^{m}} \right ]^{2}, \quad \text{if} \; S_{e}\leq 1
\\ 
1, \quad \text{if} \; S_{e} = 1
\end{cases}\].

\[ S_{e}=\frac{S_{l}-S_{r}}{1-S_{r}}\]
\[ S_{e}^{*}=\left ( 1+\left (\alpha P_{e}  \right )^{n}  \right )^{-m}\]
\[ m=\left ( 1-\frac{1}{n} \right )\]
\[ \alpha =\frac{1}{P_{r}}\]

/**NOTE**\ The above formulation is implemented in conjunction with either **ISR=5** or **ISR=55**. In case of ISR=55, it will automatically adopt the required parameters from the definition of soil water retention curve. Whereas, in case of ISR=5 (Classical Van Genuchten formulation) CSR3 will represent the gas entry pressure i.e. $P_{e}$. The definition of remaining parameters will be same. 

===== Air relative permeability =====

^IKA = 0^^  
\[k_{ra}=1\]

^IKA = 1^^  
\[k_{ra} = (1-S_e)^{CKA1}(1-S_e^{CKA2})\] \[S_e=\frac{S_{rw}-S_{rw,u}}{1-S_{rw,u}}\] 
Example: CKA1 = 2; CKA2 = 5/3

^IKA = 2^^   
\[k_{r,a}=CKA1\]

^IKA = 3^^   
\[S_e = \frac{S_{r,w}-S_{r,u}}{1-S_{rw,u}} \\ \begin{cases} \text{If } S_e<0 => S_e = 0 \\ \text{If } 0<S_e<0.55 => k_{ra}=(0.55-S_e)^{CKA1}(1-S_e^{CKA2}) \\ \text{If } S_e>0.55 => k_{ra}=k_{rmin} \end{cases} \] 
Remark:  \[k_{w,effectif}=k_{f,intrinsic}k_{rw} \\ k_{a,effectif}=k_{f,intrinsic}k_{aw}\]

^IKA = 6^^   
\[k_{ra}=\sqrt{1-S_{r,w}}\left(1-S_{r,w}^{\frac{1}{CKA1}}\right)^{2CKA1}\]

^IKA = 7^^  
\[k_{ra}=\sqrt{1-S_{we}}\left(1-S_{we}^{\frac{1}{CKA1}}\right)^{2CKA1}\] 
\[S_e=\frac{S_{rw}-S_{rw,res}}{1-S_{rw,res}-S_{rg,res}}\] \[S_{rw,res}=CKA2\] 
\[S_{rg,res}=CKA3\]

^IKA = 8^^  
\[k_{ra}=CKA2(1-S_{we})^{CKA1}\] 
\[S_e=\frac{S_{rw}-S_{rw,res}}{1-S_{rw,res}-S_{rg,res}}\]

^IKA = 55, Relative permeability function for gas considering gas entry pressure (EURAD-Gas Task4.2). ^^ 

Similar to **ISR = 55**, $p_c$ is the capillary pressure ($p_c=p_{air}-p_{water}$), $α$ is the inverse of air-entry pressure i.e., $P_r$, $S_e$ is the effective degree of water saturation, $S_l$ is the degree of water saturation, $S_r$  is residual degree of water saturation, $S_e^*$ is the effective degree of saturation considering the explicit gas entry pressure i.e., $P_e$, $m$ and $n$  are fitting parameters. Additionally, $f_{g}$ is the ratio of intrinsic permeability values for Gas ($K_{Gas}$) to Water ($K_{Water}$).

\[ k_{rg}= \begin{cases} f_{g}\sqrt{1-S_{e}}\left [ \frac{\left ( 1-\left (S_{e}^{*}\right )^{1/m} \right )^{m}-\left ( 1-\left (S_{e}^{*}S_{e} \right )^{1/m} \right )^{m}}{\left ( 1-\left (S_{e}^{*}\right )^{1/m} \right )^{m}-1} \right ]^2, \quad \text{if} \; S_{e}\leq 1
\\ 
0, \quad \text{if} \; S_{e} = 1
\end{cases}\].
\[ f_{g}=\frac{K_{Gas}}{K_{Water}}\]
\[ S_{e}=\frac{S_{l}-S_{r}}{1-S_{r}}\]
\[ S_{e}^{*}=\left ( 1+\left (\alpha P_{e}  \right )^{n}  \right )^{-m}\]
\[ m=\left ( 1-\frac{1}{n} \right )\]
\[ \alpha =\frac{1}{P_{r}}\]


/**NOTE**\ Similar to IKW=55, the above formulation is implemented in conjunction with either **ISR=5** or **ISR=55**. In case of ISR=55, it will automatically adopt the required parameters from the definition of soil water retention curve, EXCEPT the parameter $f_{g}$. 

So, CKA1 = $f_{g}$ i.e. $\frac{K_{Gas}}{K_{Water}}$

Whereas, in case of ISR=5 (Classical Van Genuchten formulation) CSR3 will represent the gas entry pressure i.e. $P_{e}$. The definition of remaining parameters will be same except the parameter CKA1 which will represent $f_{g}$ i.e. $\frac{K_{Gas}}{K_{Water}}$.

===== Thermal conductivity =====

^  ITHERM  ^  $\Gamma_T$  ^
|  \[1\]  |  \[nS_w\Gamma_w+nS_a\Gamma_a+(1-n)\Gamma_s\]|
|  \[2\]  |  \[CLT1*S_w +CLT2\]|
|  \[3\]  |  \[CLT1 -\frac{CLT2}{1 + exp\left(\frac{S_w -CLT3}{CLT4}\right)}\]|
Lagamine

User Tools

Site Tools

Page Tools
